The aim of this research is to design and construct a semiconductor laser range finder
operating in the near infrared range for ranging and designation. The main part of the range finder is the
transmitter which is a semiconductor laser type GaAs of 0.904 mm wavelength with a beam expander,
and the receiver with its collecting optics. The characteristics of transmitter pulse width were 200ns and
threshold current 10 Amp. and maximum operating current 38 Amp. The repetition rate was set at 660 Hz
and maximum output power about 1 watt. The divergence of the beam was 0.268o. A special computer
code was used for optimum optical design and laser spot size analysis and for calculation of atmosphere
attenuation.

Mobile phones are widely used nowadays, for different application such as wireless control and monitoring due to its availability and ease of use. The implemented system is based on "global system mobile (GSM)" network by using "short message service (SMS)". The design mainly contains a GSM modem and interfacing unit circuit with microcontrollers. This system could control up to eight different electrical devices such as light, Air conditioner, washing machine and many more applications which needed in daily life in different area (House, Office, or factory, etc.). The control is done by sending a specific SMS messages from traditional or smart phone. The controlling devices are restricted to a pre-defined phone number and are set in the so

Abstract

 Experimental work from Magnetic Abrasive Finishing (MAF) tests was carried out design parameters (amplitude, and number of cycle which are formed the shape of electromagnetic pole), and technological parameters (current, cutting speed, working gap, and finishing time) all have an influence on the mechanical properties of the surface layer in MAF process. This research has made to study the effect of design and technological parameters on the surface roughness (Ra), micro hardness (Hv) and material removal (MR) in working zone. A set of experimental tests has been planned using response surface methodology according to Taguchi matrix (3⁶) with three levels and six factors

For a given loading, the stiffness of a plate or shell structure can be increased significantly by the addition of ribs or stiffeners. Hitherto, the optimization techniques are mainly on the sizing of the ribs. The more important issue of identifying the optimum location of the ribs has received little attention. In this investigation, finite element analysis has been achieved for the determination of the optimum locations of the ribs for a given set of design constraints. In the conclusion, the author underlines the optimum positions of the ribs or stiffeners which give the best results. 

In this research design was treated gap laser mathematically and practically Bashaddam model Raasi simple and new and we have found that there is a good match in the practical and theoretical results

At the beginning of the twentieth century distorting handling totalitarian phenomena of art, which can be called the stage of the test, transition from the theory of ideal theory and other realistic is not cushy, since it requires vision and reading and other concepts, and in light of this dialectic manifested research problem by asking the following Is affected by the design idealism and realism. Through the above mentioned questions, the researcher found rationale for addressing this problem, the study through his research, which is marked (idealism and realism in a comparative study design). And demonstrated the importance of research in the identification of the concept and the effectiveness of the two theories idealism and realism a

In this paper, wireless network is planned; the network is predicated on the IEEE 802.16e standardization by WIMAX. The targets of this paper are coverage maximizing, service and low operational fees. WIMAX is planning through three approaches. In approach one; the WIMAX network coverage is major for extension of cell coverage, the best sites (with Band Width (BW) of 5MHz, 20MHZ per sector and four sectors per each cell). In approach two, Interference analysis in CNIR mode. In approach three of the planning, Quality of Services (QoS) is tested and evaluated. ATDI ICS software (Interference Cancellation System) using to perform styling. it shows results in planning area covered 90.49% of the Baghdad City and used 1000 mob

Graphic design art depends on changeable cognitive systems which their relation and items relying on the accumulation of humane knowledge and thong and the humane look to the venality and his explanation to the relation between him and the venality , then the graphic design art becomes an important item of this accumulation knowledge besides , it is on kind of knowledge kinds . The technological advancement in communication lauds to increasing in communication media and design methods , where the computer and its application in graphic design promotes the design process because of it's capalebities which lead to in creasing in production process , minimizing the cost and time and achieving creative and aesthetic aspect because of it's fe

This research discussed analytically based on intellectual institutions and theoretical landscape theater as artistic phenomenon depends on the compounds interacting overlapping mechanism visualization and dazzling Whatever the dilemma it a set of Alaqcar differ among themselves but in the result unit intellectual holds through difference and diversity between trends and styles and ways in design theorist theatrics Valashkalah on apparently formed through variations and different points of view through the philosophy of transformation and interpretation and assignment to offer privacy.
Valashkalah pulled in the design theorist theatrical as system training to arrange time and place and in line with the interpretation of speech text an

The current research dealt with the symbolic significance and its effectiveness in the design of the industrial product, the aesthetic communicative discourse that embodies the imagination and human conscience. Whether according to what has been termed custom or what has been approved by traditions long ago, symbolism may be the main actor in linking the identifying components of the product. In addition, symbolism provides the user with the key to accessing a direct awareness of the product’s shape and function, as an identification of the product by stimulating the symbolic form of the consumer’s imagination and inviting him to To meditate in order to realize the implicit meaning behind these forms and thus achieve the symbolism of