A new method is characterized by simplicity, accuracy and speed for determination of Oxonuim ion in ionisable inorganic acid such as hydrochloric (0.1 - 10) ,Sulphuric ( 0.1 - 6 ),nitric ( 0.1 - 10 ), perchloric ( 0.1 - 7 ), acetic (0.1 - 100 ) and phosphoric ( 0.1 - 30 ) ( mMol.L-1 )acids. By continuous flow injection analysis. The proposed method was based on generation of bromine from the Bro-3-Br-- H3O+. Bromine reacts with fluorescein to quenches the fluorescence . A sample volume no.1 (31μl) and no.2 (35μl) were used with flow rate of 0.95 mL.min-1 using H2O line no.1as carrier stream and 1.3 mL.min-1 using fluorescein sodium salt line no.2. Linear regression of the concentration ( mMol.L-1 ) Vs quenched fluorescence gives a correlation coefficient of ( 89.33 -99.72 ) for all studies of acids in various parameters were optimized. The proposed method was applied successfully for the determination of Oxonium ion in commercial samples. Using paired t-test between the newly developed method and classical method; shows that there were no significant differences between either methods. On this basis the new method can be accepted as an alternative analytical method for determination of Oxonium ion in commercial samples.
The influence of solar activity on the predicted ionospheric temperature parameters (electron Te, Ion Ti and neutral particle Tn) have been investigated over ionospheric Iraqi region by data generated using International Reference Ionosphere (IRI) and Madrigal models, the models result have been compared during the minimum and the maximum of solar cycle 24 for the years 2009 and 2016 respectively and for an altitudes ranged from 200-1000 km. The region under consideration spans over (latitude 29.1-37.2oN; longitude 38.9-47.7oE) within Iraq territory, the purpose of this paper is to determine the affection of the solar activity represented by the (sunspot number and solar flux) on the annual behavio
... Show MoreNew nanotechnology-based approaches are increasingly being investigated for enhanced oil recovery (EOR), with a particular focus on heavy oil reservoirs. Typically, the addition of a polymer to an injection fluid advances the sweep efficiency and mobility ratio of the fluid and leads to a higher crude oil recovery rate. However, harsh reservoir conditions, including high formation salinity and temperature, can limit the performance of such polymer fluids. Recently, nanofluids, that is, dispersions of nanoparticles (NPs) in a base fluid, have been recommended as EOR fluids; however, such nanofluids are unstable, even under ambient conditions. In this work, a combination of ZrO2 NPs and the polyacrylamide (PAM) polymer (ZrO2 NPs–PAM) was us
... Show More
(61)
(59)
The survey was carried out From January to April of 2018 on macrofungi samples collected from different places in Halabja province located in north eastern parts of Iraq-Kurdistan region. This region is rich in forest trees and pasture lands with diversity of shrubs and herbs and is expected to support the growth of several macro fungal species. However, this part of Kurdistan in Iraq is still unexplored from macrofungal point of view. In this paper three species from Pezizaceae and Pyronemataceae families that belonging to (Pezizales, Ascomycota), were reported from Iraqi Kurdistan. These macrofungal species are recorded for the first time from Iraq. Also the species were identified and showing their locations distributed on a map prepared
... Show MoreThis work includes synthesis of new six membered heterocyclic rings with effective amino group using the reaction of benzylideneacetophenone (chalcone) (1) with thiourea or urea in alcoholic basic medium to form: 1,3-thiazen-2-amine (2), and 1,3-oxazin-2-amine (8) respectively. The diazotization reaction was carried out with sodium nitrite in presence of hydrochloric acid to form diazonium salts which suffered coupling reaction with naphthols and phenols in the presence of sodium hydroxide to form colored azo dyes (4-7, and 10-13). o-methylation reaction of compounds (7) and (10) yielded : 1,3-thiazin -2-yl-diazenyl (14), and 1,3-oxazin-2-yl-diazenyl (15) respectively.The new compounds were characterized using vario
... Show More
(2)
In this work, three inorganic additives were 1,1sed, these are (I) ;
tetraethyl ammonium bromodichloro phenylphsphin, (II) Chlorinated paraffine. and (ITI) a mixture of (50% by weight of each) to study the synergetic effect. These additives \'v·cre used as flame retardants with unsaturated polyester and epoxy resins.;, since these resins are industrially important and of \Vide uses in life.
Results showed efficiency of these additives to retard fl mmabillty and stop burning of resins throqght the ASTM tests used Measurement of Limiting oxygen index (LOI), &nbs
... Show MoreObjective: Evaluation of the poly ether keton keton polymer (PEKK) coating material on the commercial pure titanium disks (CP Ti) with or without laser surface structuring. Design: In vitro experimental study of PEKK polymer coated material on the CP Ti disks with or without laser surface structuring. Materials and methods: coating the surface of the commercial pure titanium (CP Ti) disks with PEKK polymer was performed via using frictional mode CO2 laser, then the samples disks analyzed by using FESEM. Results: the FESEM reveal good adherence and distribution of the PEKK coated material over the CP Ti substrate by using the frictional mode CO2 laser at 2 watt and 6 ms pulse duration. Conclusion: the frictional mode CO2 laser considered an
... Show More
(7)
This work studied the electrical and thermal surface conductivity enhancement of polymethylmethacrylate (PMMA) clouded by double-walled carbon nanotubes (DWCNTs) and multi-walled carbon nanotube (MWCNTs) by using pulsed Nd:YAG laser. Variable input factors are considered as the laser energy (or the relevant power), pulse duration and pulse repetition rate. Results indicated that the DWCNTs increased the PMMA’s surface electrical conductivity from 10-15 S/m to 0.813×103 S/m while the MWCNTs raised it to 0.14×103 S/m. Hence, the DWCNTs achieved an increase of almost 6 times than that for the MWCNTs. Moreover, the former increased the thermal conductivity of the surface by 8 times and the later by 5 times.
Zinc sulfide (ZnS) thin films were deposited on glass substrates using pulsed laser deposition technique. The laser used is the Q-switched Nd: YAG laser with 1064nm wavelength and 1Hz pulse repetition rate and varying laser energy 700mJ-1000mJ with 25 pulse. The substrate temperature was kept constant at 100°C. The structural, morphological and optical properties of ZnS thin films were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscope (AFM) and UV-VIS spectrophotometer.
(1)
The content of redox sensitive trace element (V, Co, Ni, and Mo) in the bituminous limestone of the Euphrates Formation (E. Miocene) and bituminous gypsum of the Fatha Formation (M. Miocene) in the Hit Abu-Jir village area, Anbar governorate were determined using Inductively-Coupled Plasma Mass Spectrometer (ICP-MS), in order to infer the origin of the hydrocarbon and the depositional conditions of the organic matter. Hydrocarbons species by using FTIR technique was identified as aliphatic, aromatic compound, hydroxyl acids, hydroxyl group, sulfoxide and sulfur. Bitumen occurrences in these formations is a result of the hydrocarbon seepages that moved up under high pressure along the Abu-Jir fault Zone, and then were intruded in the lime
... Show MoreObject tracking is one of the most important topics in the fields of image processing and computer vision. Object tracking is the process of finding interesting moving objects and following them from frame to frame. In this research, Active models–based object tracking algorithm is introduced. Active models are curves placed in an image domain and can evolve to segment the object of interest. Adaptive Diffusion Flow Active Model (ADFAM) is one the most famous types of Active Models. It overcomes the drawbacks of all previous versions of the Active Models specially the leakage problem, noise sensitivity, and long narrow hols or concavities. The ADFAM is well known for its very good capabilities in the segmentation process. In this
... Show More