The traction property is one of the important mechanical properties, especially the rotary parts which are subjected to constant and variable loads There are many methods used to improve this property, and the shoot peening by metal balls is considered the most critical one. the study focuses on this characteristic of steel CK35 used in many engineering applications as the rotating shafts and railway This study shows that the fatigue strength is improved by14% after shoot peening with metal balls. The study includs the rehabilitation of damaged samples as a result of fatigue corrosion. The standard solution adopted was 36% MgCl­₂ with a 30 days immersion period. These samples has been improved by 6% after it decreased by18% d

To observe the effect of media of the internal pressure on the equivalent stress distribution in the tube, an experimental study is done by constructing a testing rig to apply the hydraulic pressure and three dies are manufactured with different bulging configurations (square, cosine, and conical). In the other part, ANSYS APDL is generated to analyze the bulging process with hydraulic and rubber (natural and industrial) media. It was found that when the media is a rubber, the stress is decreased about 9.068% in case of cosine die and 5.4439% in case of conical die and 2.8544% in case of square die. So, it can be concluded that the internal pressure in the rubber media is much better than in hydraulic media. Also, the force needed for fo

There are many applied Economic studies that have found positive nexus between financial development and poverty reduction in developing countries. Iraq has witnessed an increasing rate of poverty during the period 1980-2010 due to many internal and external factors such as wars, economic sanctions, inflation, a high rate of unemployment, and political and security instability. Therefore, the investigation about the solutions to reduce poverty becomes very necessary, and enhancing the financial development in Iraq is one of these options. This is due to that the financial development could reduce the poverty rates through two channels: the first is direct via the offering of the loans and other financial facilities to the poor, a

Partial shading is one of the problems that affects the power production and the efficiency of photovoltaic module. A series of experimental work have been done of partial shading of   monocrystalline PV module; 50W, I_sc: 3.1A, V_oc: 22V with 36 cells in series is achieved. Non-linear power output responses of the module are observed by applying various cases of partial shading (vertical and horizontal shading of solar cells in the module). Shading a single cell (corner cell) has the greatest impact on output energy. Horizontal shading or vertical shading reduced the power from 41W to 18W at constant solar radiation 1000W/m² and steady state condition. Vertical blocking a column

This work describes the weathering effects (UV-Irradiation, and Rain) on the thermal conductivity of PS, PMMA, PS/PMMA blend for packaging application. The samples were prepared by cast method at different ratios (10, 30, 50, 70, and 90 %wt). It was seen that the thermal conductivity of PMMA (0.145 W/m.K), and for PS(0.095 W/m.K), which increases by PS ratio increase up to 50% PS/PMMA blend then decreased that was attributed to increase in miscibility of the blend involved. By UV-weathering, it was seen that thermal conductivity for PMMA increased with UV-weathering up to (30hr) then decreased, that was attributed to rigidity and defect formation, respectively. For 30%PS/PMMA, there results showed unsystematic decrease in thermal conduct

􀀨􀀅􀀆􀀔􀀜􀀄􀀂􀀆􀀈􀀓􀀌􀀩􀀏􀀆􀀉􀀅􀀆􀀉􀀅􀀉􀀚􀀝􀀔􀀄􀀗􀀉􀀚􀀆􀀂􀀓􀀚􀀁􀀔􀀄􀀓􀀅􀀆􀀄􀀂􀀆􀀔􀀓􀀆􀀃􀀂􀀔􀀄􀀟􀀉􀀔􀀃􀀆􀀔􀀜􀀃􀀆􀀛􀀃􀀜􀀄􀀗􀀚􀀃􀀆􀀗􀀌􀀄􀀔􀀄􀀗􀀉􀀚􀀆􀀂􀀘􀀃􀀃􀀊􀀂􀀆􀀓􀀖􀀆􀀓􀀛􀀃􀀌􀀔􀀁􀀌􀀅􀀄􀀅􀀕􀀢􀀆􀀪􀀜􀀃􀀆􀀄􀀅􀀛􀀃􀀂􀀔􀀄􀀕􀀉􀀔􀀄􀀓􀀅􀀂􀀆 􀀉􀀌􀀃􀀆􀀙􀀉􀀂􀀃􀀊􀀆􀀓􀀅􀀆􀀉􀀁􀀔􀀓􀀟􀀓􀀙􀀄􀀚􀀃􀀆􀀚􀀉􀀔􀀃􀀌􀀉􀀚􀀆􀀂􀀘􀀉􀀗􀀃􀀆􀀟􀀄􀀊􀀂􀀔􀀆􀀔􀀜􀀃􀀆􀀗􀀃􀀅􀀔􀀃􀀌􀀚􀀄􀀅􀀃􀀂􀀆􀀓􀀖􀀆􀀔􀀜􀀃􀀆􀀙􀀉􀀂􀀃􀀆