The behavior corrosion inhibition of aluminum alloy (Al6061) in acidic (0.1 M HCl) and saline (3.5% NaCl) solutions was investigated in the absence and the presence of expired diclofenac sodium drug (DSD) as a corrosion inhibitor. The influence of temperature and was studied using electrochemical techniques. In addition, scanning electron microscopy (SEM) was used to study the surface morphology. The results showed that DSD acted as a powerful inhibitor in acidic solutions, while a moderate influence was observed with saline one. Maximum inhibition efficiency was 99.99 and 83.32% in acidic and saline solutions at 150 ppm of DSD, respectively. Corrosion current density that obtained using electrochemical technique was increased with temperature and decreased with the addition of DSD in both, acidic and saline solutions. DSD acted as a mixed-type corrosion inhibitor in acidic solution, while it affected the cathodic reaction in saline solution. Scanning electron microscopy (SEM) showed a significant surface damages in the absence of DSD. Quantum chemical theoretical studies were also addressed. Three states of DSD were considered in understanding the mechanism of inhibition. Normal, dissociated, and protonated states were optimized using Density Function Theory (DFT). Highest occupied molecular orbital (HOMO), lowest unoccupied molecular orbital (LUMO), energy gap (ΔE), dipole moment (µ), and other parameters were used to compare the performance of DSD states. Theoretical studies showed that the protonated state gave higher protection efficiency.
ABSTRACT: Thin film of CdS has been deposited onto clean glass substrate by using Spray pyrolysis technique. Results of Morphological (AFM) studied; electrical properties and optical conductivity studied are analysis. AFM results show a crystalline nature of the films. From the conductivity measurement at different temperatures, the activation energy of the films was calculated and found to be between 0.188 - 0.124 eV for low temperature regions, and between 1.67-1.19eV for high temperature regions. Hall measurements of electrical properties at room temperature show that the resistivity and mobility of CdS polycrystalline films deposited at 400 C0, were 3.878x103 . cm and 1.302x104cm2/ (V.s), respectively. The electrical conductivity of th
... Show MorePoly [2-methoxy-5-(2-ethylhexyloxy)-1, 4-phenylenevinyl] (MEH-PPV) thin films were created in this study using both spin coating and drop casting processes. MEH-PPV thin films generated by Ferric Chloride (FeCl3) doping (0.03, 0.06, 0.09, and 0.12 wt%) were studied for some physical features using Fourier-Transform Infrared Spectroscopy (FTIR), Field Emission Scanning Electron Microscopy (FE-SEM), and Energy Dispersive X-ray Spectroscopy (EDX). An FTIR test showed that there was no chemical reaction that occurred between Ferric Chloride (FeCl3) and MEH-PPV, but rather a physical one, that is, an organic material composite occurred. As for FE-SEM, the pure sample MEH-PPV formed uniformly, but when FeCl3 was added by weight, we have differ
... Show MoreThe successive international changes in the economic, political, cultural and other fields resulted in many phenomena that occupied different levels of interest, and have been followed up, studied and analysed by specialists and researchers especially under the development of the media in the global communication.
Even though these phenomena had reflections in the communication domain like development and changes in the mechanism of behaviours between the international communities, they created in the meantime a phenomenon that caused an imbalance in the production, spread and the use of the informations that were supposed to be for fewer than 5 countries whereas it actually it is for more than 180 countries.
The fouling depositions of crude oil stream were studied theoretically in a shell and tube heat exchanger to investigate the effect of depositions on the heat transfer process. The employed heat exchanger was with steam flowing in the inner tubes and crude oil in the shell at different velocities and bulk temperatures. It is assumed that fouling occurs only on the heated stream side (crude oil). The analysis was carried out for turbulent flow heat transfer conditions with wide range of Reynolds number, bulk temperature and time. Many previously proposed models for fouling resistance were employed to estimate a new model for fouling rate. It is found that the fouling rate and consequently the heat transfer coefficient were affected by Rey
... Show MoreThis study aims to evaluate the effect of aqueous extract stem of dried of Senna Alexandrıa using male mıce once daily at varying doses for 2 and weeks on hematological and histological changer in liver and kidney. In the acute toxicity aqueous extracted of dried stem of Senna Alexandrıa were administrated orally to mice up to 20-25 gr of body weight, in sub-acute study mice was daily administrated orally with same extraction at dose 500,1000,2000 mg/kg for 14 days . Hematological findings have shown in male group increase of RBC, HGB, HCT in increase of PIT in group treated with 500mg/ kg of body weight.
Body weight was increase after application of extract at the dose of 1000 and 2000 mg/ kg . T
... Show MoreThe spectrum known represented as a relationship that’s plotted between the magnitudes or energy for a specific parameter vs. its frequency, the wind spectrum is presented as the sum of wind speed created by events divided either in space, in time, or both. This paper presents a wind speed spectrum demonstration in
Ali Al-Gharbi location in Iraq. The aim of the present paper is to analysis the wind speed and direction by employing the FFT (Fast Fourier Transform) therefore field measurement of wind speed and direction were collected for one year from Dec 2014 to Dec 2015 in the time interval of 10 minutes at heights of 10, 30 and 50
meters. From the performance of the FFT it was found that the v
Friction Stir Welding (FSW) is one of the most effective solid states joining process and has numerous potential applications in many industries. A FSW numerical tool, based on ANSYS F.E software, has been developed. The amount of the heat gone to the tool dictates the life of the tool and the capability of the tool to produce a good processed zone. Hence, understanding the heat transfer aspect of the friction stir welding is extremely important for improving the process. Many research works were carried out to simulate the friction stir welding using various softwares to determine the temperature distribution for a given set of welding conditions. The objective of this research is to develop a finite element sim
... Show MoreSchiff Base And Ligand Metal Complexes of Some Amino Acids and Drug
The liver of marsh harrier grossly appeared as large, bi-lobed organ divided into left and right lobes, which are approximately equal in size and not divided into secondary lobes. Histologically, the liver of marsh harrier was found to contain numerous lobules which are not well defined by the connective tissue of the septa except that surrounded the portal triads. The parenchyma of liver composed of irregular branching cords of hepatocytes organized in double rows alternating with tortures path sinusoids which are lined with flattened endothelial cells and large, irregular outlined kupffer cells. Hepatic cords arranged in a radial pattern around the central vein of the liver lobule while in a subscapsular region they run parallel to the ca
... Show MoreThe proton, neutron and matter density distributions, the corresponding size radii and elastic electron scattering form factors of one-proton8B and two-proton 17Ne halo nuclei are calculated. The theoretical technique used to fulfill calculations is by assuming that both nuclei under study are composed of two main parts; the first is the compact core and the second is the unstable halo part. The single-particle radial wavefunctions of harmonic-oscillator (HO) and Woods-Saxon (WS) potentials are used to study core and halo parts, respectively. And other approach is studied by using HO potential for both core and halo parts, but using two HO size parameters for both supposed parts. The long ta
... Show More