Lithium-based rechargeable batteries (LbRBs) are essential for applications in vehicles, wearable electronics, and large-scale energy storage due to their high energy density. However, safety concerns associated with flammable organic electrolytes hinder further development. Advancing Li-ion battery technology requires improved conductivity, energy density, and safety, particularly in the development of all-solid-state lithium-ion batteries (ASSLiBs). This work explores carboxymethyl cellulose (CMC)-based solid polymer electrolytes (SPEs) as sustainable alternatives for lithium-ion batteries. The synergistic effects of 1-butyl-3-methyl imidazolium chloride ([BMIm]Cl) ionic liquid, as a plasticizer, and lithium acetate (LiCH3COO) enhance the electrochemical properties of SPE membranes. A wrinkled morphology and optimal ionic transport are achieved at 30 wt.-% [BMIm]Cl, labeled as SPE30-IL30, as evidenced by scanning electron microscopy (SEM) and Fourier-transform infrared (FTIR) spectroscopy. SPE30-IL30 exhibit excellent thermal stability up to 508 degrees C, with a crystallinity index (Cr.I) of 43.73 % and stiffness of 48.55x10-3 GPa. At 30 wt.-% [BMIm]Cl, the CMC-based membrane achieves an ionic conductivity of 1.37 x 10-3 S cm-1, a lithium-transference number (tLi+) of 0.96, and an electrochemical stability window of 3.85 V, representing the highest performance among the studied SPEs. Density functional theory (DFT) simulations further reveal that [BMIm]Cl reduces the stabilization energy of LiCH3COO by 14 kcal/mol, strengthening molecular interactions between CMC and Li+ ions. These results highlight the potential of [BMImCl] ionic liquid-plasticized CMC-based SPEs as a sustainable, high-performance electrolytes for next-generation ASSLiBs, aligning with circular economy principles while delivering enhanced electrochemical and physicochemical properties.
The Gaussian orthogonal ensemble (GOE) version of the random matrix theory (RMT) has been used to study the level density following up the proton interaction with 44Ca, 48Ti and 56Fe.
A promising analysis method has been implemented based on the available data of the resonance spacing, where widths are associated with Porter Thomas distribution. The calculated level density for the compound nuclei 45Sc,49Vand 57Co shows a parity and spin dependence, where for Sc a discrepancy in level density distinguished from this analysis probably due to the spin misassignment .The present results show an acceptable agreement with the combinatorial method of level density.
... Show MoreTwisting and coiling actuators (TCAs) are lightweight artificial muscles that can produce large linear contractions while lifting heavy loads with low power. A TCA consists of two or more strings connected to a rotational motor and a load. When activated, the strings twist and coil, causing contraction. This study presents a data-driven framework for modeling TCA behavior using experimental data. Polynomial regression, Support Vector Regression (SVR), and symbolic regression were applied using the motor angle and payload weight as inputs. The models were evaluated under various loads and implemented in a neck-rehabilitation prototype. SVR showed the highest accuracy (RMSE: 6.17 mm upward, 4.98 mm downward); however, it lacks a closed-form e
... Show MoreThis study used deep eutectic solvent (DES) as the liquid membrane in a bulk liquid membrane system (BLM) to remove glycerol from waste cooking oil‐based biodiesel. The DES was prepared from choline chloride and tetraethylene glycol at a molar ratio of 1:5. Diethyl ether was employed as a novel strip phase for the glycerol in BLM. The effects of the DES: biodiesel ratio, stirring speed, and extraction time on the extraction and stripping efficiencies were investigated. The results showed that BLM could give better glycerol removal from biodiesel than mechanical shaking. Increasing the DES: biodiesel ratio, stirring speed, and extraction time can enhance glycerol removal from the feed phase, achievi
Various approaches are employed to enhance the heat transfer coefficient and Nusselt number inside the channels. One of the techniques employed for these enhancements is the utilization of porous media. In the current article, a practical investigation of forced convection heat transfer in a rectangular cross‐section channel (0.05 × 0.1 m2) with 0.25 m length is conducted. A heater with a heat flux range (450–6000 W/m2) is imposed under a copper plate, and the other sides are covered by insulation layers. The air is considered as a working fluid with
Human relationships are shaped and affected by the place they live in. This article analyzes Lynn Nottage’s Sweat from the perspective of spatial theory, particularly using the theories of Yi-Fu Tuan and Doreen Massey, to explore the complex connection between place and human relationships. The article examines how Nottage presents the reciprocal effect between people and their setting. By examining the city, the factory, and the local community around it, the study shows how place serves as a dynamic force that shapes the characters’ identities and relationships rather than just serving as a background. While Massey’s concept of place as a product of social relations offers a framework to explore the tensions and solidarity that aris
... Show MoreFusidic acid (FA) is a well-known pharmaceutical antibiotic used to treat dermal infections. This experiment aimed for developing a standardized HPLC protocol to determine the accurate concentration of fusidic acid in both non-ionic and cationic nano-emulsion based gels. For this purpose, a simple, precise, accurate approach was developed. A column with reversed-phase C18 (250 mm x 4.6 mm ID x 5 m) was utilized for the separation process. The main constituents of the HPLC mobile phase were composed of water: acetonitrile (1: 4); adjusted at pH 3.3. The flow rate was 1.0 mL/minute. The optimized wavelength was selected at 235 nm. This approach achieved strong linearity for alcoholic solutions of FA when loaded at a serial concentrati
... Show More
