Foreign trade receives a good deal of economists' attention for its active contribution to economic growth, and imports of goods and services that could not be produced locally constitute an important share of the local economy.  Agricultural imports constitute an important share of the total imports due to their role in fulfilling the needs of local markets; however, the agricultural sector in Iraq contributes no more than a limited share of the country's need, which has encouraged the import of a variety of fruits, vegetables and strategic crops and different types of red and white meat. For the sake of identifying the factors affecting the demand on agricultural imports in Iraq, the following factors has been analyzed: th

This thesis aims to study the effect of addition polymer materials on mechanical properties of self-compacting concrete, and also to assess the influence of petroleum products (kerosene and gas oil) on mechanical properties of polymer modified self-compacting concrete (PMSCC) after different exposure periods of (30 ,60 ,90 ,and 180 days).

Two type of curing are used; 28 days in water for SCC and 2 days in water followed 26 days in air for PMSCC.

The test results show that the PMSCC (15% P/C ratio) which is exposed to oil products recorded a lower deterioration in compressive strength's values than reference concrete. The percentages of reduction in compressive strength values of PMSCC (15% P/C ratio) was

In this study, composite materials were prepared using unsaturated polyester resin as binder with two types of fillers (sawdust and chopped reeds). The molding method is used to prepare sheets of UPE / sawdust composite and UPE / chopped reeds composite. The mechanical properties were studied including flexural strength and Young's modulus for the samples at normal conditions (N.C). The Commercial wood, UPE and its composite samples were immersed in water for about 30 days to find the weight gain (Mt%) of water for the samples, also to find the effect of water on their flexural strength and Young's modulus. The results showed that the samples of UPE / chopped reeds composite gained highest values of flexural strength (24.

Breast cancer (BC) is the most prevalent tract cancer in the world, including Iraq. The classified breast tumors to benign, malignant, and radiotherapy. Cancer treatment depends on certain stages such as mastectomy then chemotherapy alone or with radiation therapy or endocrine therapy according to the prognostic features obtained from the pathology report. The present study included 100 females. The women were split into two groups, control group that consisted of 50 apparently healthy females and 50 patients with BC group who undergo the radiotherapy. The current study highlighted on some of the anthropometric measurements, including the oxidative stress index malondialdehyde (MDA), the concentrations of total antioxidant capacity (TAC), s

Abstract

In the present work, thermal diffusivity and heat capacity measurements have been investigated in temperature range between RT and 1473 K for different duplex stainless steel supplied by Outokumpu Stainless AB, Sweden. The purpose of this study is to get a reliable thermophysical data of these alloys and to study the effect of microstructure on the thermal diffusivity and heat capacity value. Results show the ferrite content in the duplex stainless steel increased with temperature at equilibrium state. On the other hand, ferrite content increased with increasing Cr/Ni ratio and there is no significant effect of ferrite content on the thermal diffusivity value at room temperature. Furthermore, the heat capacity of all sam

In this work, yttrium oxide particles (powder) reinforced AL-Si matrix composites (Y2O3/Al-Si) and Chromium oxide particles reinforced AL-Si matrix composites (Cr2O3/AL-Si) were prepared by direct squeeze casting. The volume percentages of yttrium oxide used are (4, 8.1, 12.1, 16.1 vol %) and the volume percentages of the chromium oxide particles used are (3.1, 6.3, 9.4, 12.5 vol. %). The parameters affecting the preparation of Y2O3/Al-Si and Cr2O3/AL-Si composites by direct squeeze casting process were studied. The molten Al-Si alloy with yttrium oxide particles or with chromium oxide particles was stirred again using an electrical stirrer at speed 500 rpm  and the molten alloy was  poured  into the squeeze die cavity. Th