As part of our research on efficiency improvement of PERC (Passivated Emitter Rear Solar Cell), achieving very low reflectivity values of solar cell surface is a must. One of the most advance technologies to do so is the use of advanced texturing for the front surface of the cells. This texture, also known as Black Silicon, consists of peaks and valleys of nano metric dimensions and capable of dramatically reducing the reflectance of the front surface. A reflectance around 5%  was reached ,using simulation, when using a Black-Silicon texturing with height of 50nm with peak rounding of 5nm. Even though this texturing may affect other parameters such as series resistance or surface recombination, as a starting point

Background: Blood vessels injury is one of the most
common causes of medical emergencies that admitted to
hospitals and at the same time it regarded as one of the
most important causes of death. They may represent less
than 15% of all injuries; they deserve special attention
because of their severe complications.
Objective: The aim of the present study is to assess
anatomically the injures of major arteries and veins in the
lower limb with their management.
Methods: The present study extended from April 2006 to
February 2007, in which 65 patients with lower limb
vascular injury were examined in Emergency Department
and Forensic Medicine Department of Tikrit Teaching
Hospital in Salah-Aldin governora

In the present work, it had been measured the concentration of radon gas (C_Rn) for (10) samples of cement used in constructions before and after painting them using enamel paint, purchased from the local markets, to see the extent of its ability to reduce emissions of Rn-222 in the air. These samples were obtained from different sources available in the local markets in Baghdad and other provinces. The measurements were done by the American-made detector (RAD7). The results showed that the highest C_Rn in the air emitted from cement samples after coating was in the cement sample (Iranian origin) where the concentration was (58.27 Bq/m³) while the lowest C_Rn was found in building material samples

In this work, silicon nitride (Si₃N₄) thin films were deposited on metallic substrates (aluminium and titanium sheets) by the DC reactive sputtering technique using two different silicon targets (n-type and p-type Si wafers) as well as two Ar:N₂ gas mixing ratios (50:50 and 70:30). The electrical conductivity of the metallic (aluminium and titanium) substrates was measured before and after the deposition of silicon nitride thin films on both surfaces of the substrates. The results obtained from this work showed that the deposited films, in general, reduced the electrical conductivity of the substrates, and the thin films prepared from n-type silicon targets using a 50:50 mixing ratio and deposited on both

The photo-electrochemical etching (PECE) method has been utilized to create pSi samples on n-type silicon wafers (Si). Using the etching time 12 and 22 min while maintaining the other parameters 10 mA/cm² current density and HF acid at 75% concentration.. The capacitance and resistance variation were studied as the temperature increased and decreased for prepared samples at frequencies 10 and 20 kHz. Using scanning electron microscopy (SEM), the bore width, depth, and porosity % were validated. The formation of porous silicon was confirmed by x-ray diffraction (XRD) patterns, the crystal size was decreased, and photoluminescence (PL) spectra revealed that the emission peaks were centered at 2q of 28.5619° and 28.7644° for et

Roller compacted concrete (RCC) is a special type of concrete with zero or even negative slump consistency. In this work, it had aimed to produce an RCC mix suitable for roads paving with minimum cost and better engineering properties so, different RCC mixes had prepared i.e. (M1, M2, M3, and M4) using specified percentages of micro natural silica sand powder (SSP) as partial replacement of (0%, 5%, 10%, and 20%) by weight of sulfate resistant Portland cement. Additionally, M-sand, crushed stone, filler, and water had been used. The results had obtained after 28 days of water curing. The control mix (M1) had satisfied the required f ‘c with accepted results for the other tests. M2 mix with SSP of 5% had

Suitability of groundwater for irrigation depends upon many constrains factors, these factors depend upon the dissolved salts during the flow of the recharge of the groundwater beside the aquifer constituents itself, from these factors (EC, SO4-2, Cl-, Na%, and SAR) .The spatial distribution of each constrain factor may show discrepancy from the another, so it is not possible to depend upon one factor. The aim of this work is to present a classification of the groundwater quality for agriculture including all the mentioned five factors, by using Arc GIS which provides tools to serve a purpose to create conceptual model for solving spatial problems. A set of conceptual steps used to build a model for suitability map of groundwater for irr

Back ground: A urinary tract infection is one of the most common diseases occurring from neonate up to geriatric age groups
Patients and Methods: A total of (100) Midstream urine (MSU) samples were collected from patients having signs and symptoms of Lower urinary tract infection. These patients were attending Urology Clinic, Ramadi General Hospital.
Result: Culturing of (100) MSU samples on MacConky and blood agar resulted in (5) types of bacteria which included: Escherichia coli (46%) and it was found the most frequent bacteria causing LUTI. This is followed by Klebsiella pneumonia (23%), Pseudomonas aeruginosa (13%), Proteus mirabilis (10%) and Staphylococcus epidermidis (8%).
Conclusion: Out of

Back ground: A urinary tract infection is one of the most common diseases occurring from neonate up to geriatric age groups
Patients and Methods: A total of (100) Midstream urine (MSU) samples were collected from patients having signs and symptoms of Lower urinary tract infection. These patients were attending Urology Clinic, Ramadi General Hospital.
Result: Culturing of (100) MSU samples on MacConky and blood agar resulted in (5) types of bacteria which included: Escherichia coli (46%) and it was found the most frequent bacteria causing LUTI. This is followed by Klebsiella pneumonia (23%), Pseudomonas aeruginosa (13%), Proteus mirabilis (10%) and Staphylococcus epidermidis (8%).
Conclusion: Out of