Abstract Introduction: MMP3 plays a crucial role in the process of bone erosion in the pathomechanism of rheumatoid arthritis (RA). It acts by removing the outer osteoid layer, which allows the osteoclasts to tightly connect and carry out the subsequent damage to the underlying bone. MMP3 can trigger the production of other MMPs like MMP-1, MMP-7, and MMP-9, it plays a pivotal role in the remodeling of connective tissues. Aim of the study: to assess the influence of MMP-3 serum levels and single-nucleotide polymorphisms of rs679620 in the rheumatoid arthritis patients' group in comparison to the control group. Subjects: eighty eight samples, 45 rheumatoid arthritis patients after being referred by their treating physician for regular RA test. The remaining 43 samples all represent apparently healthy people. The present study investigated the serum concentration of MMP-3 and rs679620 SNPs in the group of patients with RA, in comparison to the control group. Results: The results indicated a significant elevation in MMP-3 levels in RA patients in comparison to healthy individuals (12.75 ± 0.38 vs. 9.69 ± 0.37) and the findings of rs679620 SNPs appeared that the patient group has a non-significant increase in both allele frequency A and genotype frequency AA when compared to the control group (66.2 vs. 52.2 %; p = 0.172; OR = 1.79 and 35.3 vs. 17.4 %; p = 0.229; OR = 2.59) , but a non-significant decrease in both allele frequency C and genotype frequency CC when compared to the control group (2.94 vs. 4.4 %; p = 1.0; OR = 0.67 and 2.9 vs. 4.3 %; p = 1.0; OR = 0.67), as well as a non-significant decrease in allele frequency G and both genotypes frequency GG and AG when compared to the control group (30.9 vs. 43.5 %; p = 0.233; OR = 0.58, 0.0 vs. 8.7 %; p = 0.159; OR = 0.12 and 61.8 vs. 69.6 %; p = 0.585; OR = 0.71 ). Patients carrying the AA and AG genotype, had significantly higher serum levels of MMP-3 compared to control (P= 0.005 and 0.004) respectively. Conclusion: Rs679620 may influence joint destruction via increase MMP-3 production.
(30)
(30)
Background: Medical-surgical nurses are responsible of providing competent care to clients with a wide-array of acute and chronic health problems. This challenging task requires arming nurses with advanced competencies of health literacy to effectively educate their clients. However, evidence about medical-surgical nurse’s health literacy-related knowledge and experience is limited. Purposes: This study aimed to determine the level of the health literacy-related knowledge and experience among medical-surgical nurses.Design: A descriptive-cross-sectional study was conducted among a total sample of 177 nurses who were practicing in medical-surgical wards in teaching hospitals in Iraq. A convenience sampling method was used to sele
... Show More
(5)
(1)
Shear lag is the phenomenon that occurs when a supported slender member undergoes deformation from lateral loading, causing in-plane non-uniform distribution of stresses that results in reducing the member’s minimum strength capacity. This paper investigates the behaviour of shear distribution in steel I-section and box girders when subjected to both static and impact loadings. Three-dimensional finite element analysis models were prepared in Strand7 and validated against experimental results providing a basis for further comparison research into shear lagging effects. A parametric study was conducted comparing the effects of impact loading through certain specified velocities at the midspan of restrained ends. It provided new ins
... Show More
Objective: The aim of this study was to compare the marginal microleakage between bulk-fill, preheated bulk-fill, and bulk-fill flowable composite resins above and below cemento-enamel junction (CEJ) using micro-computed tomography. Methods: Sixty freshly extracted premolar teeth were prepared with a slot shaped cavities of a total of 120 Class II: 3mm (bucco-lingual), 2mm (mesio-distal) with mesial-gingival margin located 1mm coronal to CEJ, and distal gingival margin located 1mm apical to the CEJ. The samples were randomly divided into two main groups according to the restorative material (Tetric EvoCeram and 3M Filtek), and each group was further sub-divided into three subgroups according to the consistency (bulk fill, preheated bulk fil
... Show More
(9)
(5)
The aim of the research is to identify the reality of administrative motivation for the deans of the faculties of physical education and sports sciences at the universities of Baghdad and Al-Mustansiriya from the point of download of the faculty members. The number of the exploratory sample was (7) faculty members, they were taken in a random way, while the rest of the sample number was (150) faculty members who considered the application sample for the scale, and the two researchers also adopted a questionnaire for the scale and it is applied to the Iraqi environment. phrase, which are phrases that are interrelated with the administrative leadership motivation in the faculties of physical education and sports sciences. The researchers did
... Show More
(1)
An experimental study was performed to estimate the forced convection heat transfer performance and the pressure drop of a single layer graphene (GNPs) based DI-water nanofluid in a circular tube under a laminar flow and a uniform heat flux boundary conditions. The viscosity and thermal conductivity of nanofluid at weight concentrations of (0.1 to 1 wt%) were measured. The effects of the velocity of flow, heat flux and nanoparticle weight concentrations on the enhancement of the heat transfer are examined. The Nusselt number of the GNPs nanofluid was enhanced as the heat flux and the velocity of flow rate increased, and the maximum Nusselt number ratio (Nu nanofluid/ Nu base fluid) and thermal performance factor
... Show More