Nasryia oil field is located about 38 Km to the north-west of Nasryia city. The field was discovered in 1975 after doing seismic by Iraqi national oil company. Mishrif formation is a carbonate rock (Limestone and Dolomite) and its thickness reach to 170m. The main reservoir is the lower Mishrif (MB) layer which has medium permeability (3.5-100) md and good porosity (10-25) %. Form well logging interpretation, it has been confirmed the rock type of Mishrif formation as carbonate rock. A ten meter shale layer is separating the MA from MB layer. Environmental corrections had been applied on well logs to use the corrected one in the analysis. The combination of Neutron-Density porosity has been chosen for interpretation as it is close to core porosity. Archie equation had been used to calculate water saturation using corrected porosity from shale effect and Archie parameters which are determined using Picket plot. Using core analysis with log data lead to establish equations to estimate permeability and porosity for non-cored wells. Water saturation form Archie was used to determine the oil-water contact which is very important in oil in place calculation. PVT software was used to choose the best fit PVT correlation that describes reservoir PVT properties which will be used in reservoir and well modeling. Numerical software was used to generate reservoir model using all geological and petrophysical properties. Using production data to do history matching and determine the aquifer affect as weak water drive. Reservoir model calculate 6.9 MMMSTB of oil as initial oil in place, this value is very close to that measured by Chevron study on same reservoir which was 7.1 MMMSTB. [1] Field production strategy had been applied to predict the reservoir behavior and production rate for 34 years. The development strategy used water injection to support reservoir pressure and to improve oil recovery. The result shows that the reservoir has the ability to produce oil at apparently stable rate equal to 85 Kbbl/d, also the recovery factor is about 14%.
Objective: Per-implantitis is one of the implant treatment complications. Dentists have failed to restore damaged periodontium by using conventional therapies. Tissue engineering (stem cells, scaffold and growth factors) aims to reconstruct natural tissues. The paper aimed to isolate both periodontal ligament stem cells (PDLSCs) and bone marrow mesenchymal stem cells (BMMSCs) and use them in a co-culture method to create three-layered cell sheets for reconstructing natural periodontal ligament (PDL) tissue. Materials and methods: BMMSCs were isolated from rabbit tibia and femur, and PDLSC culture was established from the lower right incisor. The cells were co-cultured to induce BMMSC differentiation into PDL cells. Cell morphology, stem cel
... Show MoreConventional identification of three coccoid green algae isolates was attempted to characterize the studied algae morphologically under compound microscope, which demonstrated confusional phenomenal convergence; all were classified microscopically as the green alga Chlorella vulgaris Beijerinck, 1890.
Phylogenetic studies were conducted to settle the argument about the phenotype by studying the genotype. Genotype the promising field in advance classification by using 18S rRNA and compared to GenBank database using to search the related sequences. The determined sequences showed high a similarity to the strains registered in GenBank.
&
... Show MoreThe novel Vierordt’s approach, or simultaneous equation method, was created and validated for the concurrent determination of vincristine sulfate (VCS) and bovine serum albumin (BSA) in pure solutions utilizing UV spectrophotometry. It is simple, precise, economical, rapid, reliable, and accurate. This method depends on measuring absorbance at two wavelengths, 296 nm and 278 nm, which correspond to the λmax of VCS and BSA in deionized water, respectively. The calibration curves of VCS and BSA are linear at concentration ranges of 10–60 μg/mL and 200–1600 μg/mL, with correlation coefficient values (R2) of 1 and 0.999, respectively. The limits of detection (LOD) and quantification (LO
... Show MoreIn this research, titanium dioxide nanoparticles (TiO2 NPs) were prepared through the sol-gel process at an acidic medium (pH3).TiO2 nanoparticles were prepared from titanium trichloride (TiCl3) as a precursor with Ammonium hydroxide (NH4OH) with 1:3 ratio at 50 °C. The resulting gel was dried at 70 °C to obtain the Nanocrystalline powder. The powder from the drying process was treated thermally at temperatures 500 °C and 700 °C. The crystalline structure, surface morphology, and particle size were studied by using X-ray diffraction (XRD), Atomic Force Microscopy (AFM), and Scanning Electron Microscope (SEM). The results showed (anatase) phase of titanium dioxide with the average grain size
... Show MoreABSTRACT:
The study aims at expounding the correlation and effect between the Human resource development strategy and Quality Municipality Service within a theoretical framework and a practical framework conducted at Directorate Of Municipalities in holy Karbala . The researcher found during a pilot study that there isn’t enough care paid by the Directorate Of Municipalities in developing its human resources using one strategy or a number of strategies and their effect on the Quality Municipality Service. Thus a number of research questions were set concerning the existence of clear perception in the Directorates Of Municipalities concerning the strategies of developing both the human resource an Qualit
... Show More