The main objective of this research is to find out the effect of deviation in the aggregate gradients of asphalt mixtures from the Job Mix Formula (JMF) on the general mixture performance. Three road layers were worked on (wearing layer, binder layer, and base layer) and statistical analysis was performed for the data of completed projects in Baghdad city, and the sieve that carried the largest number of deviations for each layer was identified. No.8 sieve (2.36mm), No.50 sieve (0.3mm), and 3/8'' sieve (9.5mm) had the largest number of deviations in the wearing layer, the binder layer, and the base layer respectively. After that, a mixture called Mix 1, was made. This mixture was selected from a number of completed mixtures, and it represents the worst mixture. Mix 1 was compared with two other mixtures, Mix 2 and Mix 3, Mix 2 represents the mean of JMF for the gradients of aggregates, and Mix 3 is the same as Mix 1 except for the sieve that contains the largest number of deviations, so the gradient of aggregates for it is the mean of JMF. Fifteen Marshall specimens were made for each mixture and for each layer in order to know the differences in Marshall properties between the mixtures. Also, 6 specimens were made for each mixture (the total is 18 specimens for each layer) to check the indirect tensile strength, for the purpose of knowing the mixtures' susceptibility to moisture. Finally, 1 specimen was made for each mixture for repeated load test for the purpose of knowing the performance of the mixtures with respect to permanent deformation. The tests showed that the performance of Mix 2 and Mix 3 was improved in comparison with Mix 1. The deviation of the aggregate gradients in specific sieves may be higher than the limits of the JMF or it may be less, and in both cases, the implementation of a mixture like Mix 1 for the streets is bad for the performance of the road and failures occur due to the wrong implementation of the JMF. On the other hand, there are much better mixtures in all respects such as Mix 2 and Mix 3, and if they are implemented on the streets, they will certainly have much better.
Schiff bases were prepared prepared Baaan NMR to some elements of which have contributed to the results of different methods in diagnosis prove structural formulas of compounds prepared
Activated carbon was Produced from coconut shell and was used for removing sulfate from industrial waste water in batch Processes. The influence of various parameter were studied such as pH (4.5 – 9.) , agitation time (0 – 120)min and adsorbent dose (2 – 10) gm.
The Langmuir and frandlich adsorption capacity models were been investigated where showed there are fitting with langmmuir model with squre regression value ( 0.76). The percent of removal of sulfate (22% - 38%) at (PH=7) in the isotherm experiment increased with adsorbent mass increasing. The maximum removal value of sulfate at different pH experiments is (43%) at pH=7.
The world is confronted with the twin crisis of fossil fuel depletion and environmental degradation caused by fossil fuel usage. Biodiesel produced from renewable feedstocks such as Jatropha seed oil or animal fats by transesterification offers a solution. Although biodiesel has been produced from various vegetable oils such as Jatropha seed oil, the reaction kinetics studies are very few in literature, hence the need for this study. Jatropha curcas seed oil was extracted and analyzed to determine its free fatty acid and fatty acid composition. The oil was transesterified with methanol at a molar ratio of methanol to oil 8:1, using 1% sodium hydroxide catalyst, at different temperature
... Show MoreThis study aims to test ceramic waste's capacity to remove nickel from aqueous solutions through adsorption. Ceramic wastes were collected from the Refractories Manufacturing Plant in Ramadi. Through a series of lab tests, the reaction time (5, 10, 15, 20, 25, 30, 35, 40, 45, and 50 minutes, and Ni concentrations (20, 40, 60, and 80) were tested using ceramic wastes with a solid to liquid ratio of 2g/30ml. At a temperature of 30ºC, the pH, total dissolved solids (TDS), and electrical conductivity (EC) were all measured. The equilibrium time was set at 30 min. Thereafter, the sorption (%) somewhat increased positively with the Ni concentration. Freundlich's equation showed that the adsorption intensity is 1.1827 and the Freundlich c
... Show MoreIn this study, measuring effectiveness Alauriz in some seeds powder and found that the seeds of-sophistication sex had the highest effective enzymatic reach 353 units / gProtein and Alkabbatah study enzyme extract under different storage conditions and Altaj showed that the enzyme loses Thbatih and whether Mrkbhetwan adding Alklasrin concentration of 10% for the systematic solution
The sole aim of the tribe of the Messenger of Allah (PBUH) and his basilica was to revoke the Umayyad heresy and to refute the suspicions through which they climbed to the top of the pyramid of power and legitimized the leadership of Muslims (heresy of hereditary rule) with the sword and blood. Therefore, Imam Hussein (peace be upon him) began his Ashura process with his short divine message in its words and great in its vocabulary and content and even the future of Mohammedan Islam over the times and spaces - what we will see in the folds of research, God willing.
Among a collection of ground beetles from Iraq the new species Acinopus euphraticus was designated and described here. The erection of this new species was mainly built on external features and the description of male genitalia.
Experimental activity coefficients at infinite dilution are particularly useful for calculating the parameters needed in an expression for the excess Gibbs energy. If reliable values of γ∞1 and γ∞2 are available, either from direct experiment or from a correlation, it is possible to predict the composition of the azeotrope and vapor-liquid equilibrium over the entire range of composition. These can be used to evaluate two adjustable constants in any desired expression for G E. In this study MOSCED model and SPACE model are two different methods were used to calculate γ∞1 and γ∞2