Anumerical solutions is presented to investigate the effect of inclination angle (θ) , perforation ratio (m) and wall temperature of the plate (T_w) on the heat transfer in natural convection from isothermal square flat plate up surface heated (with and without concentrated hole). The flat plate with dimensions of (128 mm) length × (64 mm) width has been used five with square models of the flat plate that gave a rectangular perforation of (m=0.03, 0.06, 0.13, 0.25, 0.5). The values of angle of inclination were (0^o, 15^o 30^o 45^o 60^o) from horizontal position and the values of wall temperature (50^oC, 60 ^oC, 70 ^oC, 90 ^oC, 100^o<

The adsorption ability of Iraqi initiated calcined granulated montmorillonite to adsorb of 4-(4-Nitrobenzeneazo) 3-Aminobenzoic Acid from aqueous solutions has been investigated through columnar method. The azo dye adsorption found to be dependent on adsorbent dosage, initial concentration and contact time. All columnar experiments were carried out at three different pH values (5.5, 7and 8) using buffer solutions at flow rate of (3 drops/ min.), at room temperature (25±2) °C. The experimental isotherm data were analyzed using Langmuir, Freundlich and Temkin equations. The monolayer adsorption capacity is 6.4066 mg Azo ligand per 1g calcined Montmorillonite. The experiments showed that highest removal rate 90.5 % for azo dye at pH 5.5.The

Background: Denture fracture is one of the most common problems encountered by the patients and prosthodontists. The objective of present study was to evaluate the transverse strength of nylon denture base resin repaired by using conventional heat polymerized, autopolymerized and visible light cure {VLC} resins, surface treatment that used for repair and adjustment of insufficient nylon denture bases and in case of addition of artificial teeth. As these corrective procedures are common chair side procedures in dental clinic. Materials and methods: One hundred twenty nylon specimens were prepared by using metal patterns with dimension of (65x10x2.5 mm) length, width, and thickness respectively for transverse strength test while for tensile b

Background: Polymethyl methacrylate (PMMA) is the most commonly used material in denture fabrication. The material is far from ideal in fulfilling the mechanical requirements. Midline fracture; poor thermal conductivity and water sorption, are common problem in this material. The purpose of this study was to evaluate the effect of addition of surface treated Aluminum oxide nano fillers on some properties of heat cured (PMMA). Materials and methods: In addition to controlled group of heat cured PMMA the silanized (Al2O3) nanoparticles was added to PMMA powder by weight in three different percentages 1wt%, 2wt% and 3wt%, mixed by probe ultra-sonication machine. 200 specimens were constructed and divided into 5 groups according to the test (e

A total of 45 voucher specimens of falcons which are deposited in the bird's collection of the Iraq Natural History Research Center and Museum (INHM) were reviewed. Mummified falcons were preserved as voucher study specimens and tagged with museum collection labels. In the current study, morphometrics of six species of the genus Falco Linnaeus, 1758: Lanner falcon F. biarmicus Temminck, 1825; Sacker Falcon F. cherrug Gray, 1834; Lesser Kestrel F. naumanni Fleischer, 1818; Peregrine Falcon F. peregrines Tunstall, 1771; Eurasian Hobby F. subbuteo Linnaeus, 1758 and Common Kestrel F. tinnunculus Linnaeus, 1758 were documented. These species were recorded previously in the ornithological literatures by several authors and deposited in t

A total of 45 voucher specimens of falcons which are deposited in the bird's collection of the Iraq Natural History Research Center and Museum (INHM) were reviewed. Mummified falcons were preserved as voucher study specimens and tagged with museum collection labels. In the current study, morphometrics of six species of the genus Falco Linnaeus, 1758: Lanner falcon F. biarmicus Temminck, 1825; Sacker Falcon F. cherrug Gray, 1834; Lesser Kestrel F. naumanni Fleischer, 1818; Peregrine Falcon F. peregrines Tunstall, 1771; Eurasian Hobby F. subbuteo Linnaeus, 1758 and Common Kestrel F. tinnunculus Linnaeus, 1758 were documented. These species were recorded previously in the ornithological literatures by several authors and deposited in t

This paper reports a numerical study of flow behaviors and natural convection heat transfer characteristics in an inclined open-ended square cavity filled with air. The cavity is formed by adiabatic top and bottom walls and partially heated vertical wall facing the opening. Governing equations in vorticity-stream function form are discretized via finite-difference method and are solved numerically by iterative successive under relaxation (SUR) technique. A computer program to solve mathematical model has been developed and written as a code for MATLAB software. Results in the form of streamlines, isotherms, and average Nusselt number, are obtained for a wide range of Rayleigh numbers 10³-10⁶ with Prandtl number 0.71

A total of 45 voucher specimens of falcons which are deposited in the bird's collection of the Iraq Natural History Research Center and Museum (INHM) were reviewed. Mummified falcons were preserved as voucher study specimens and tagged with museum collection labels. In the current study, morphometrics of six species of the genus Falco Linnaeus, 1758: Lanner falcon F. biarmicus Temminck, 1825; Sacker Falcon F. cherrug Gray, 1834; Lesser Kestrel F. naumanni Fleischer, 1818; Peregrine Falcon F. peregrines Tunstall, 1771; Eurasian Hobby F. subbuteo Linnaeus, 1758 and Common Kestrel F. tinnunculus Linnaeus, 1758 were documented.
These species were recorded previously in the ornithological literatures by several authors and deposited in the

This research investigated the effect of adding two groups of reinforcement materials, including bioactive materials Hydroxyapatite (HA) and halloysite nanoclay and bioinert materials Alumina (AL2O3) and Zirconia (ZrO2), each of them with various weight ratios (1,2,3,4 &5)% to the polymer matrix PMMA. The best ratios were selected, and then a hybrid was preparing Composite red from the best ratios from each group. Thermal properties, including thermal conductivity and Thermomechanical Analysis (TMA) technology, have been studied. The results showed that adding 3% Hydroxyapatite (HA) and 5% halloysite nanoclay to the polymethacrylate (PMMA) mer leads to an increase in thermal conductivity. It was also found from the Thermomechanical Analysis