The effect of different cutting fluids on surface roughness of brass alloy workpiece during turning operation was carried out in this research. This was performed with different cutting speed, while other cutting parameters had been regarded as constants(feeding rate , and depth of cut). Surface roughness of machined parts that will be tested by electronic surface roughness tester .The results show that the standard coolant gives the best values of surface roughness for fixed cutting speed ,followed by sun flower oil that has approximately the same effect, while the air stream as a coolant gave unsatisfied results for the evaluation of surface roughness.

In the other hand the best values of surface roughness were recorded for max

The use of composite materials has vastly increased in recent years. Great interest is therefore developed in the damage detection of composites using non- destructive test methods. Several approaches have been applied to obtain information about the existence and location of the faults. This paper used the vibration response of a composite plate to detect and localize delamination defect based on the modal analysis. Experiments are conducted to validate the developed model. A two-dimensional finite element model for multi-layered composites with internal delamination is established. FEM program are built for plates under different boundary conditions. Natural frequencies and modal displacements of the intact and damaged

A Strength Pareto Evolutionary Algorithm 2 (SPEA 2) approach for solving the multi-objective Environmental / Economic Power Dispatch (EEPD) problem is presented in this paper. In the past fuel cost consumption minimization was the aim (a single objective function) of economic power dispatch problem. Since the clean air act amendments have been applied to reduce SO2 and NOX emissions from power plants, the utilities change their strategies in order to reduce pollution and atmospheric emission as well, adding emission minimization as other objective function made economic power dispatch (EPD) a multi-objective problem having conflicting objectives. SPEA2 is the improved version of SPEA with better fitness assignment, density estimation, an

 In this paper, a study of the earthquakes that have affected Baghdad region in Iraq is made" The documents collected from different references a

This study concerns the control of movement of Dense Non-Aqueous Phase Liquid (DNAPL) in saturated zone in the presence of relatively low permeability lens. A two-dimensional, finite-difference numerical model for the simultaneous movement of the DNAPL and water through the saturated zone of the soil is developed. The system is, actually, a three fluid phase system (water, DNAPL and air) but in the derivation of the model, air was treated as an immobile phase at constant atmospheric pressure. The flow equations for Dense Non-Aqueous Phase Liquid and water are cast in terms of the wetting and non-wetting fluid pressure heads respectively. The finite- difference equations are solved fully implicitly using Newton-Raphson iteration scheme wi

The aim of this paper is to evaluate the effect of the converter system on the power factor of the supply network .Therefore a 3-phase, 6-pulse , bridge converter is assembled and connected to a power supply through a 3-phase ac voltage regulator .The theoretical analysis is simulated using Fourier series analysis and Fast Fourier Transform ( FFT ) algorithm . The experimental measurements of distortion factor , displacement factor and total power factor are recorded . The experimental results are shown to be coincident with the theoretical results. The consideration of power factor improvement relative to distortion and displacement factors is discussed.

Modified asphalt is considered one of the alternatives to address the problems of deficiencies in traditional asphalt concrete, as modified asphalt addresses many of the issues that appear on the pavement layers in asphalt concrete, resulting from heavy traffic and vehicles loaded with loads that exceed the design loads and the large fluctuations in the daily and seasonal temperatures of asphalt concrete. The current study examined the role of polyphosphoric acid (PPA) as a modified material for virgin asphalt when it was added in different proportions (1%, 2%, 3%, 4%) of the asphalt weight. The experimental program includes the volumetric characteristics associated with the Marshall test, the physical properties, and th

Mixed convection heat transfer in a vertical concentric annulus packed with a metallic porous media and heated at a constant heat flux is experimentally investigated with water as the working fluid. A series of experiments have been carried out with a Rayleigh number range from Ra=122418.92 to 372579.31 and Reynolds number that based on the particles diameter of Re_d=14.62, 19.48 and 24.36. Under steady state condition, the measured data were collected and analyzed. Results show that the wall surface temperatures are affected by the imposed heat flux variation and Reynolds number variation. The variation of the local heat transfer coefficient and the mean Nusselt number are presented and analyzed. An empirical

One aspect of interest in robotics is planning the optimum path for a mobile robot or the optimum trajectory for link movements of a stationary robot in order to increase their efficiency. The objective of this paper is to identify the sequence of steps and processes needed for construction off line path planning system using genetic algorithm (as we coined GPPS). In off-line path planning. the robot is given a map with the location of all obstacles in a given world. The goal is to construct the shortest possible path between a pre-defined start and goal positions and then follow this path without running into the obstacles. In addition to the three basic genetic operators, a new operator is proposed here which is coined as repair operat

Non photorealistic rendering is a new research field in the areas of computer graphics. The goal is to give a more natural feel to computer generated images, by simulating various artistic techniques and to give the sense of an image without reproducing it. In this paper, we present a new evolutionary approach to non-photorealistic rendering of 2D black/white and grayscale images. The goal is to generate a painting that is close to a given input image. This problem can be formalized as a high-dimensional optimization problem, with local minima. We have developed a genetic algorithm that modifies the traditional uniform crossover to spread out vital genes at the expense of lethal genes rather than exchanging them between matting parents.

Greywater is a possible water source that can be improved for meeting the quality required for irrigation. Treatment of greywater can range from uncomplicated coarse filtration to advanced biological treatment. This article presents a simple design of a small scale greywater treatment plant, which is a series of physical and natural processes including screening, aeration, sedimentation, and filtration using granular activated carbon filter and differentiates its performance with sand filter. The performance of these units with the dual filter media of (activated carbon with sand) in treatment of greywater from Iraqi house in Baghdad city during 2019 and that collected from several points including washbasins, kitchen si

In this paper, a dynamic investigation is done for strip, rectangular and square machine foundation at the top surface of two-layer dry sand with various states (i.e., loose on medium sand and dense on medium sand). The dynamic investigation is performed numerically using finite element programming, PLAXIS 3D. The soil is expected as a versatile totally plastic material that complies with the Mohr-Coulomb yield criterion. A harmonic load is applied at the base with an amplitude of 6 kPa at a frequency of (2 and 6) Hz, and seismic is applied with acceleration – time input of earthquake hit Halabjah city north of Iraq. A parametric study is done to evaluate the influence of changing L/B ratio (Length=12,6,3 m and width=3 m), type of sand

This investigation presents an experimental and analytical study on the behavior of reinforced concrete deep beams before and after repair. The original beams were first loaded under two points load up to failure, then, repaired by epoxy resin and tested again. Three of the test beams contains shear reinforcement and the other two beams have no shear reinforcement. The main variable in these beams was the percentage of longitudinal steel reinforcement (0, 0.707, 1.061, and 1.414%). The main objective of this research is to investigate the possibility of restoring the full load carrying capacity of the reinforced concrete deep beam with and without shear reinforcement by using epoxy resin as the material of repair. All be

Cell-free massive multiple-input multiple-output (CF-MIMO) system has been considered a promising technology for 5G and 6G networks for its ability to handle the rise in demand effectively. With CF-MIMO, improved energy efficiency can be obtained from straightforward signal processing. One of the potential problems in CF-MIMO systems is high power consumption due to the large numbers of distributed Access Points (APs), which decrease energy efficiency. This research proposes a modified algorithm to improve overall energy efficiency by reducing total power consumption via using the APs selection technique while maintaining the system's sum of rate. The technique used for APs selection is the largest large-scale-based sele

The research focuses on determination of best location of high elevated tank using the required head of pump as a measure for this purpose. Five types of network were used to find the effect of the variation in the discharge and the node elevation on the best location. The most weakness point was determined for each network. Preliminary tank locations were chosen for test along the primary pipe with same interval distance. For each location, the water elevation in tank and pump head was calculated at each hour depending on the pump head that required to achieve the minimum pressure at the most weakness point. Then, the sum of pump heads through the day was determined. The results proved that there is a most economical lo

Multi-belled piles are piles with enlarged ends; these piles have one or further bells at the lower third part of the pile. These piles are suitable for many soils with problems such as softening clay, the variation of groundwater table, expansive soils, black cotton soil, and loose sand. The current study reviewed the behavior of belled piles in multi-layer soils subjected to axial compression and pullout loading. The review covered the experimental and theoretical works on belled piles in multi-layered soils. These piles were subjected to static and dynamic loadings in compression and pullout cases. Most theoretical results focused on software such as PLAXIS 3D. The axial load applied on the piles comes from the upper

Dairy wastewater generally contains fats, lactose, whey proteins, and nutrients. Casein precipitation causes the effluent to decompose into a dark, strong-smelling sludge. Fluid waste contains soluble organic matter, suspended solids, and gaseous organic matter, which cause undesirable taste and smell, grant tone and turbidity, and advance eutrophication, which plays an essential role in increasing biological oxygen demand (BOD) in water. It also contains detergents and disinfecting agents from the rinses and washing processes, which increase the need for chemical oxygen (COD). One of the characteristics of dairy effluents is their relatively high temperature, high organic contents, and wide pH range, so the discharge of wastewater into

The aim of the present work to study the effect of changing velocity (Reynold's number) on oxygen cathodic polarization using brass rotating cylinder electrode in 0.1, 0.3 and 0.5N NaCl solutions (PH = 7) at temperatures 40, 50 and 600 C. Cathodic polarization experiments were conducted as a function of electrode rotational speed and concentration.

One of the artificial lightweight aggregates with a wide range of applications is Lightweight Expanded Clay Aggregate. Clay is utilized in the production of light aggregates. Using leftover clay from significant infrastructure development projects to manufacture lightweight aggregates has a favorable environmental impact. This research examines the expanded clay aggregate production process and the impact of processing parameters on its physical and mechanical qualities. It also looks at secondary components that can be used to improve the qualities of concrete with expanded clay aggregates. The effect of the quantity of expanded clay aggregate on the fresh, hardened, and durability qualities of concrete is also studied.

Many researchers used different methods in their investigations to enhance the heat transfer coefficient, one of these methods is using porous medium. Heat transfer process inside closed and open cavities filled with a fluid-saturated porous media has a considerable importance in different engineering applications, such as compact heat exchangers, nuclear reactors and solar collectors. So, the present paper comprises a review on natural, forced, and combined convection heat transfer inside a porous cavity with and without driven lid. Most of the researchers on this specific subject studied the effect of many parameters on the heat transfer and fluid field inside a porous cavity, like the angle of inclination, the presenc

During the last decade, there has been a concern about the relation between aluminum residuals in treated water and Alzheimer disease, and more interest has been considered on the development of natural coagulants. The present study aimed to investigate the efficiency of alum as a primary coagulant in conjunction with mallow, Arabic gum and okra as coagulant aids for the treatment of water samples containing synthetic turbidity of kaolin. Jar test experiments were carried out for initial raw water turbidities 100, 200 and 500 (NTU). The optimum doses of alum, mallow, Arabic gum and okra were 20, 2, 1 and 1 mg/L for100 NTU turbidity level, 35, 4, 2 and 3 mg/L , for 200NTU turbidity level and 50, 8, 10 and 8 mg/L for 500 NTU turbidity leve

 Heritage is considered as the civilization and cultural wealth accumulated over the . centuries, whereas architectural heritage is the physical witness of that civilization. Despite the fact that architectural heritage is the most important effort for economic development of any communit,، it suffers from deterioration and neglection especially in the Arab communities. Recently awareness has increased about the importance of investing on architectural heritage generally and sustainable investment particularly. The goal of investment process in heritage areas is to revive economic activity in addition to attempt to revive the heritage and community values. Research aims to examine the relationship between sustainable investment and

Geotechnical engineering involves many different and complex materials and many different mechanisms of behaviour. The direct use of experience as a guide to the prediction and design is effective provided these are understood. Geotechnical engineering is a relatively new science. Its successful application to prediction requires realistic assumptions to be made, and predictions must be tested against reality. Methods of prediction need then to be refined. An example of the importance of making realistic assumptions is examined in this paper. It includes the effects of soil properties on the ultimate capacity of axially loaded piles.
Better analysis offers better prediction and better understanding. Both are only possible when reality

This paper describes an experimental study on the performance of sulfamic acid and citric acid in scale removal of Dura refinery heat exchange piping systems. Experiments were carried out using sulfamic acid and citric acid inhibited by hexamine as cleaning solutions at different time, temperature and concentrations. A dynamic flow system was designed for this state. A scaled copper alloy pipes from the main hot water lines (heat exchanger) was used. Hexamine was used as corrosion inhibitor.The research involved a study of effect of the time ,temperature and acid concentration of each acid on the scale removal, and a comparison of the performance of the two used acids were investigated.

This paper presents the building of expert system to enable the inexperience plants operators to application of better of wastewater treatment plant. This methodology consists of three steps: (i) creation of a decision trees (algorithms) for the diagnosis operational problems; (ii) implementation into a real-based system; and (iii) verification. This system called expert system for Rustimiyah south wastewater treatment plant operation (ES-RS-WWTPO). The knowledge acquisitions to build this system ware extracted from literature. Moreover local experience ware also incorporated using the results of a well designed questionnaire. The results obtained in the application three operational states showed that the system was able to diagnosis (c

Construction joints are frequently used in engineering structures for various reasons. When the size of the structure is relatively large stoppage of concrete casting at certain locations is necessary. Stoppage of casting may also occurs due to sudden failure of mixing machines, or when the concrete stock ingredients runs out of materials, or when weather conditions do not permit casting operations to continue. If stoppage of concreting occurs, a joint between old and new concrete forms, it is then necessary to evaluate the horizontal shear capacity at the interface between old and new concretes to prevent progressive slip from taking place and to insure satisfactory performance of the structure.
A total of 16 push-off tests were perf

Automatic detection and classification of cardiac arrhythmias is important for diagnosis of cardiac abnormality. This paper shows a method to accurately classify ECG arrhythmias through a combination of slantlet transform and artificial neural network (ANN). The ability of the slantlet transform to decompose signal at various resolutions allows accurate extraction of features from non-stationary signals like ECG. The low frequency coefficients, which contain the maximum information about the arrhythmia, were selected from the slantlet decomposition. These coefficients are fed to a Multi-Layer Perceptron (MLP) artificial neural network which classifies the arrhythmias. In the present work the ECG data is taken from standard MIT- BIH datab

The oxidation of phenol in aqueous solution was studied at atmospheric pressure in a batch
reactor. Fenton reaction was used to degrade this component. Phenol (50 - 100 ppm) oxidation was carried out in the acidic medium range of (pH=2.7 - 5.8) under mild conditions of temperature (28 - 48°C), stochiometric excess percentage of H2O2 (S.EH2O2%) of (0 - 100%), and Fe(II) to phenol concentrations ratio of (0 - 0.63). The results indicate that the oxidation by Fenton reaction was an efficient method to eliminate phenol, also the amount of catalyst and temperature had the large effect on the phenol degradation. Finally the simple kinetic model for the reaction was established.

The objective of this study was to develop a complete package for prediction of volumetric and thermodynamic properties of pure hydrocarbons fluids and their mixtures in one and two phase regions. Two cubic equations of state that are Peng-Robinson and Soave-Redlich-Kwong were used with volatile and black oils respectively to calculate the desired properties in addition to bubble point and dew point pressures and temperatures. Different values of binary interaction parameter were used for each equation and effects of this parameter values on the prediction are examined. Also values of this parameter between the plus-fraction and other component have been evaluated for first time. In calculation of heat capacity, four different mixing rul

The research aims to use the computer and it's potential to identify and choose the best offers submitted by companies contracting with the third-expected increases in the wages of labor and prices of building materials and the large variability in the impact of the inability of many of the construction to complete the implementation of the specific time or the estimated cost and thus create a lot of problems executive, which affected the speed and quality of works. A good management and good planning through implementation to reflect the realities and possibilities of each of the contracting companies to tender for any contract so a knowledge of possibilities of each company and compare it with the other , according to the mechanism in