Collapse of the vapor  bubble condensing  in an immiscible  is investigated for  n-pentane and n-hexane vapors condensing in cold water and n-pentane in two different compositions of glycerin- water mixture. The rise velocity and the drag coefficient of the two-phase bubble are measured.

The induced electrochemical-Fenton (I-EF) process is one of the electrochemical advanced oxidation processes (EAOPs) that has been recently applied to treat various types of wastewaters. In this work, the I-EF process, comprising a graphite/SnO₂-Sb₂O₃ anode, an iron-screen-induced electrode, and an air-diffusion cathode, was used to treat petroleum refinery wastewater. The effects of current density (2-10 mA/cm²), pH (3-7), and the number of screens on the induced electrode (1 and 4) on chemical oxygen demand (COD) removal were investigated. Results showed that increasing pH improved COD removal, whereas increasing current density beyond 3 mA/cm2 reduced it. Increasing the screen number also enhanced the

   Gas lift is one of the most important artificial lift methods for increasing oil production, as wells often require this method after the reservoir's energy has decreased. In this research, an optimal gas lift system is designed for five horizontal wells in the Ahdab oil field, which suffers from low production. At the same time, water cut in some of these wells reaches 66%, while the productivity index is low in others, which makes the challenges clear, and a deep analysis is needed to find an optimal system. The Pipesim program is used to design the optimal gas lift system, which contains features that facilitate the implementation of the appropriate design and provide the ability to analyze and determine the optimal design values

   This research paper uses pipesim software to reproduce and evaluate well performance, comparing vertical and horizontal wells using hydraulic fracturing. It examines the impact of key parameters, such as fracture length, width, permeability, and fracture number, on production improvement. In low-permeability reservoirs, simulation studies indicate that horizontal wells often achieve higher production rates than vertical wells, largely due to improved reservoir and fracture connectivity. Productivity in the vertical well increased to 300(stb/d), while in the horizontal well, it increased to over 9,000 (stb/d) after using hydraulic fracturing. The results indicate that fracture width has less of an impact on the performance of vertica

Drag has long been identified as the main reason for the loss of energy in fluid transmission like pipelines and other similar transportation channels. The main contributor to this drag is the viscosity as well as friction against the pipe walls, which will results in more pumping power consumption.

   The aim in this study was first to understand the role of additives in the viscosity reduction and secondly to evaluate the drag reduction efficiency when blending with different solvents.

   This research investigated flow increase (%FI) in heavy oil at different flow rates (2 to 10 m3/hr) in two pipes (0.0381 m & 0.0508 m) ID By using different additives (toluene and naphtha) with different concent

 تضمن البحث قياس المواصفات الفيزياوية والكيميائية والاحيائية للمياه الخام والمنتجة في ثلاث محطات تصفية في محافظة المثنى خلال ثلاثة عشر شهرا شملت محطة تصفية كل من الرميثة والوركاء والخضر لغرض تقييم نوعية مياه النهر (الخام) ومياه الشرب (المنتجة) ومقارنتها مع المواصفة القياسية العراقية للمياه وقد شملت المواصفات الفيزياوية دراسة عكورة المياه والتوصيلية الكهربائية فيه, اما المواصفات الكيميائي

   Pressure retarded osmosis (PRO) can be considered as one of the methods for utilizing osmotic power, which is a membrane-based technology. Mathematical modeling plays an essential part in the development and optimization of PRO energy-generating systems. In this research, a mathematical model was developed for the hollow fiber module to predict the power density and the permeate water flux theoretically. Sodium chloride solution was employed as the feed and draw solution. Different operating parameters, draw solution concentration (1 and 2 M), the flow rate of draw solution (2, 3, and 4 L/min), and applied hydraulic pressure difference (0 - 90 bar) was used to evaluate the performance of PRO process of a hollow fiber module. The eff

   The economical and highly performed anode material is the critical factor affecting the efficiency of electro-oxidation toward organics. The present study aimed to detect the best conditions to prepare Mn-Co oxide composite anode for the electro-oxidation of phenol. Deposition of Mn-Co oxide onto graphite substrate was investigated at 25, 30, and 35 mA/cm² to detect the best conditions for deposition.  The structure and the crystal size of the Mn-Co oxide composite electrode were examined by using an X-Ray diffractometer (XRD), the morphological properties of the prepared electrode were studied by scanning electron microscopy (SEM) and Atomic force microscopy (AFM) techniques, and the chemical composition of the various

In this study, sulfur was removed from imitation oil using oxidative desulfurization process. Silicoaluminophosphate (SAPO-11) was prepared using the hydrothermal method with a concentration of carbon nanotubes (CNT) of 0% and 7.5% at 190 °C crystallization temperature. The final molar composition of the as-prepared SAPO-11 was Al₂O₃: 0.93P²O⁵: 0.414SiO². 4% MO/SAPO-11 was prepared using impregnation methods. The produced SAPO-11 was described using X-ray diffraction (XRD) and Brunauer-Emmet-Teller (N² adsorption–desorption isotherms). It was found that the addition of CNT increased the crystallinity of SAPO-11. The results showed that the surface area of SAPO-11 cont

   This paper deals with the development of a casing program on a well called A4-1 (for confidentiality reasons) for safe and cost-effective production. The data used are geological data and information on different depths. To achieve the paper's objective, first, the different casing installation depths are determined using Excel software, and the mud program required for drilling, as well as the different casing diameters, are found through analysis of the tool selection diagram. After calculating the various pressures and loads, the drilling handbook is used to select the different grades for each casing. The results show that, at a depth of 6480 feet, the surface casing has a diameter of 11"3/4, weight of 65 ppf, and grade K55. At

The lead-acid battery has become so dependable in its used applications of automobile starting, emergency lighting and telecommunications, which left an impression that no further investigation is necessary or desirable. While there has been slow continuous improvements in lead-acid battery performance and mainly limited to design and material engineering. This work is mainly devoted to the properties of the active mass of the positive electrode and the acid/water ratio during the manufacturing process. A field study is carried out at the State Battery Manufacturing Company located in Baghdad, to prepare batches of lead mono-oxide with predefined quantities of liquid additives (i.e. sulfuric acid and water). Quality control and laborator

Efficient and cost-effective drilling of directional wells necessitates the implementation of best drilling practices and advanced techniques to optimize drilling operations. Failure to adequately consider drilling risks can result in inefficient drilling operations and non-productive time (NPT). Although advanced drilling techniques may be expensive, they offer promising technical solutions for mitigating drilling risks. This paper aims to demonstrate the effectiveness of advanced drilling techniques in mitigating risks and improving drilling operations when compared to conventional drilling techniques. Specifically, the advanced drilling techniques employed in Buzurgan Oil Field, including vertical drilling with mud motor, managed pres

The Jeribe reservoir in the Jambour Oil Field is a complex and heterogeneous carbonate reservoir characterized by a wide range of permeability variations. Due to limited availability of core plugs in most wells, it becomes crucial to establish correlations between cored wells and apply them to uncored wells for predicting permeability. In recent years, the Flow Zone Indicator (FZI) approach has gained significant applicability for predicting hydraulic flow units (HFUs) and identifying rock types within the reservoir units.

   This paper aims to develop a permeability model based on the principles of the Flow Zone Indicator. Analysis of core permeability versus core porosity plot and Reservoir Quality Index (RQI) - Normalized por

Isobaric Vapor-Liquid-Liquid equilibrium data for the binary systems ethyl acetate + water, toluene + water and the ternary system toluene + ethyl acetate + water were determined by a modified equilibrium still, the still consisted of a boiling and a condensation sections supplied with mixers that helped to correct the composition of the recycled condensed liquid and the boiling temperature readings in the condensation and boiling sections respectively. The VLLE data where predicted and correlated using the Peng-Robinson Equation of State in the vapor phase and one of the activity coefficient models Wilson, NRTL, UNIQUAC and the UNIFAC in the liquid phase and also were correlated using the Peng-Robinson Equation of State in both the vapo

   Typically, sandstone oil reserves comprise various clay minerals, such as illite, chlorite, and kaolinite. The existence of these clay minerals drastically affected the quality of these reservoirs. This paper attempts to detect clay minerals and environmental deposition of the upper shaly-sand unit (USSU) of the Nahr Umar formation, as it is the main reservoir. It is a portion of an anticline composed of a lower Cretaceous clastic sandstone formation. The kind of environment, clay minerals, and depositional correlation between total organic matter and uranium content were determined using a spectral log of gamma-ray (SGR). According to the SGR log, the primary constituents of USSU are mixed-layer clays, which are

The Pb²⁺ ions biosorption removal onto dead biomass of Chlorophyta algae is optimized by employing response surface methodology (RSM). Central composite design (CCD)-based experiments were carried out, and RSM was used to evaluate the results. The effects of contact time (15-120min), with pH solution (2-7), initial lead concentration (25-100 mg/L), biomass dose (0.01-1 g/100 mL), agitation speed (100-300 rpm) on the biosorption process were investigated. The optimal conditions of the experimental, data were pH (5), metal concentration (50mg/L), dosage (0.2g/100mL), agitation speed (200 rpm), and contact time of 120 min with constant particle size (63 mm), which gave 98.88% removal efficiency. All the

Insulin like growth factor-1 has metabolic and growth-related roles all over the body and is strongly associated and regulated by growth hormone. It is produced by almost any type of tissue, especially the liver. The study aimed to measure insulin like growth factor in growth hormone deficient patients and find its relation with other studied parameters. The Subjects in the study were 180 studied in the National Diabetic Center for Treatment and Research/Al-Mustansiriya University in Baghdad/Iraq for the period from November 2021 to April 2022. Blood was drawn and investigated for the levels of IGF-1, IGFBP-3, LH, and FSH. Also testosterone and statistical analysis was carried out to find the potential correlations. The results relived t

Coffee is the most essential drink today, aside from water, the high consumption of coffee and the byproducts of its soluble industries such as spent coffee grounds can have a negative effect on the environment as a source of toxic organic compounds. Therefore, caffeine removal from the spent coffee ground can be applied as a method to limit the effect of its production on the environment. The aim of this study is to determine the kinetics and thermodynamics parameters and develop models for both processes based on the process parameters by using traditional solid-liquid extraction and Ultrasound-assisted extraction methods. The processes were performed at a temperature range of 25 to 55 °C for traditional and ultrasound baths, and expe

   This study presented Intelligent Network's proposed methodology for forecasting the effectiveness of cadmium removal from wastewater using emulsion liquid membrane (ELM). The research examined the removal of cadmium from an aqueous solution in the internal phase of water-in-oil emulsions. ELM was composed of kerosene as the membrane phase, Span 80 as the surfactant, di-2-ethylhexyl phosphoric acid (D₂EHPA) as the extracting agent, and hydrochloric acid (HCl) as the stripping solution. Experiments were conducted to investigate the effects of five parameters: surfactant concentration, feed-phase agitation speed, internal-to-membrane phase volume ratio, emulsion-to-feed volume ratio, and stripping-phase concentration in the

Empirical equations for estimating thickening time and compressive strength of bentonitic - class "G" cement slurries were derived as a function of water to cement ratio and apparent viscosity (for any ratios). How the presence of such an equations easily extract the thickening time and compressive strength values of the oil field saves time without reference to the untreated control laboratory tests such as pressurized consistometer for thickening time test and Hydraulic Cement Mortars including water bath ( 24 hours ) for compressive strength test those may have more than one day.

The finishing operation of the electrochemical finishing technology (ECF) for tube of steel was investigated In this study. Experimental procedures included qualitative
and quantitative analyses for surface roughness and material removal. Qualitative analyses utilized finishing optimization of a specific specimen in various design and operating conditions; value of gap from 0.2 to 10mm, flow rate of electrolytes from 5 to 15liter/min, finishing time from 1 to 4min and the applied voltage from 6 to 12v, to find out the value of surface roughness and material removal at each electrochemical state. From the measured material removal for each process state was used to verify the relationship with finishing time of work piece. Electrochemi

One of the major elements faced in downhole drilling operations of oil and gas wells is the limited reach of coiled tubing (CT) in horizontal wellbores. To address this issue, this work creates an extended reach limit simulation of CT with starting bending curvature in a horizontal wellbore for an Iraqi well in the Ahdeb oil field. Using Drillbench software, a calculation approach is provided based on contact force and buckling models to determine the extended reach limit of CT. The findings of this study have significant implications for improving downhole drilling engineering design parameters and predicting the extended reach limit of CT. By considering factors such as friction resistance and contact force between the wellbore, a more

   The mechanical characteristics of rocks such as elasticity (Young's modulus, Poisson's ratio, and unconfined compressive strength) play an essential in sand production analysis, well design, and borehole stability assessment. In this study, the mechanical characteristics of rocks were indirectly estimated using gamma ray, density, and acoustic (compressional and shear) log data from well RU-X in the Rumaila oil field, specifically for the Zubair Formation. These estimated properties were compared to direct measurements obtained from triaxial and uniaxial mechanical tests conducted on well RU-X. The results showed a significant similarity between the indirect estimates and the direct measurements, indicating their reliability for san

Room temperature ionic liquids show potential as an alternative to conventional organic membrane solvents mainly due to their properties of low vapour pressure, low volatility and they are often stable. In the present work, the technical feasibilities of room temperature ionic liquids as bulk liquid membranes for phenol removal were investigated experimentally. In this research several hydrophobic ionic liquids were synthesized at laboratory. These ionic liquids include (1-butyl-3-methylimidazolium bis (trifluoromethylsulfonyl) imide[Bmim][NTf₂], 1-Hexyl-3-methylimidazolium bis (trifluoromethylsulfonyl) imide[Hmim][NTf₂], 1-octyl-3-methylimidazolium bis (trifluoromethylsulfonyl)imide[Omim][NTf₂],1‐butyl

   Carbon dioxide (CO₂) is the primary factor considered to be responsible for global warming. CO₂ capture technology has been considered an important issue to decrease greenhouse gas emissions. The current research investigates the functionalization of Multi-Wall Carbon nanotubes (MWCNTs) by Ethylenediamine (EDA) solution which is used for CO₂ capture at various operating conditions. Surface functionality groups and morphology of MWCNTs and physical properties were analyzed by X-ray diffraction (XRD), Fourier Transforms Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), surface area Brunauer Emmett and Teller (BET). The physical and chemical properties of CNTs have changed after the func