The loose sand is subject to large settlement when it is exposed to high stresses. This settlement is due to the nature of the high drainage of sand, which displays foundations and constructions to a large danger. The densification of loose sandy soils is required to provide sufficient bearing capacity for the structures. Thus soil stabilization is used to avoid failure in the facilities. Traditional methods of stabilized sandy soil such as fly ash, bituminous, and cement often require an extended curing period. The use of polymers to stabilize sandy soils is more extensive nowadays because it does not require a long curing time in addition to being chemically stable. In this study, the effect of adding different percentages of high-density polyethylene HDPE to the sandy soils' engineering characteristics such as the angle of internal frictions Ø0, shear strength τ, California Bearing Ratio CBR, and permeability k was studied. The results of laboratory tests showed that using of HDPE at percentages (0.1, 0.3, 0.6, 1, and 3%) led to a decrease in soil permeability by 18% and an increase in both the angle of internal friction, the CBR value, and shear strength about 27.2%, 180.9%, and 38.6 % respectively by adding 1%. HDPE.
In this work; copper oxide films (CuO) were fabricated by PLD. The films were analyzed by UV-VIS absorption spectra and their thickness by using profilometer. Pulsed Nd:YAG laser was used for prepared CuO thin films under O2 gas environment with varying both pulse energy and annealing temperature. The optical properties of as-grown film such as optical transmittance spectrum, refractive index and energy gap has been measured experimentally and the effects of laser pulse energy and annealing temperature on it were studied. An inverse relationship between energy gap and both annealing temperature and pulse energy was observed.
The goal of this experimental study is to determine the effects of different parameters (Flow rate, cuttings density, cuttings size, and hole inclination degree) on hole cleaning efficiency. Freshwater was used as a drilling fluid in this experiment. The experiments were conducted by using flow loop consist of approximately 14 m (46 ft) long with transparent glass test section of 3m (9.84 ft.) long with 4 inches (101.6 mm) ID, the inner metal drill pipe with 2 inches (50.8 mm) OD settled with eccentric position positive 0.5. The results obtained from this study show that the hole cleanings efficiency become better with high flow rate (21 m3/hr) and it increase as the hole inclination angles increased from 60 to 90 degree due to dominated
... Show Morethis research seeks to shed light on the study of the impact of Putinism on the Russian-Ukrainian war that broke out in early 2022, by studying the contents of the speeches of Russian President Vladimir Putin before the start of the war. This research uses the structural approach in analyzing the components of the Russian political regime. The research tools used in this research include case studies, content analysis of Russian speeches, and personal meetings of researchers and specialists in Russian affairs. It sums up a number of important conclusions, most notably are : 1) Putinism is a totalitarian regime that includes the political doctrine during the era of Russian President Vladimir Putin. 2) Duginism represents the totality of t
... Show MoreThe aim of the study was to identify the use of the strategies of numbered heads and brainstorming in learning handspring on the Vault table in artistic gymnastics for Men for the third grade students in the collage of Physical Education and Sport Sciences, as well as to identify the best group among the three research groups (number of heads numbered,, brainstorming strategies And the traditional style group) to learn the skill under study. Using the experimental method, the research subject included the third grade students in the collage of Physical Education and Sports Sciences / University of Baghdad, and randomly by lot, 12 students were selected for each of the three research groups. The study consisted of the arithmetic mean
... Show MoreRheumatoid arthritis and periodontitis use analogous effector destructive procedures, in that the inflammatory cells and pro-inflammatory cytokines that drive chronic bone erosion in RA and chronic periodontal destruction in Periodontitis are alike. Periodontitis (PD) has appeared as a hazard factor in a number of health situations as rheumatoid arthritis (RA). To determine the effect of anti-tumor necrosis factor alpha biological treatment (methotrexate and Enbrel or infliximab) on periodontal status of patients having rheumatoid arthritis with periodontitis in comparison to those having periodontitis without rheumatoid arthritis and control healthy subjects and to determine the serum levels of anti-cyclic citrullinated peptide (ACCP) in t
... Show MoreCultured fruits of theCorundum Coriandrum sativum were sown On 11/11 / 2008 in basins containing 15 kg of soil (Silty Loam) .Fruits were divided into two parts the first was soaked in normanl water and the second was magnetized for a period of 24 hours Irrigation was up to (75% of capacity field.Two types of water (normal water and magnetized water)with three repetitions were used the access to magnetic water was supplied from a special electric device. Recorded measurements were plant height the number of stems / plant, weight of plant, number of flowers, 1000 seed weight) during the cultivation period, which ended on 11/5/2009. Results indicated the absence of any effect of magnetic water on plant growth of Fenugreek while seeds tre
... Show MoreIncremental Sheet Metal Forming (ISMF) is a modern sheet metal forming technology which offers the possibility of manufacturing 3D complex parts of thin sheet metals using the CNC milling machine. The surface quality is a very important aspect in any manufacturing process. Therefore, this study focuses on the resultant residual stresses by forming parameters, namely; (tool shape, step over, feed rate, and slope angle) using Taguchi method for the products formed by single point incremental forming process (SPIF). For evaluating the surface quality, practical experiments to produce pyramid like shape have been implemented on aluminum sheets (AA1050) for thickness (0.9) mm. Three types of tool shape used in this work, the spherical tool ga
... Show Morethe research was exposed to a study the importance of the role of the supportive entities in providing the useful information to the tax administration and their ability to extend the level of the tax base of taxpayers, through the improvement of the tax payers determination and their tax settle for the purpose of increasing the tax revenue, and shed light on the legal evidence through which these entities become officially assigned to perform a supplementary task to the General Committee for Taxes GCT, to help it to perform its task efficiently, and to study the reasons of the weak cooperation of the supportive entities and their reluctance to provide useful information which leads to limiting the tax base.
The research data hav
... Show MoreThe current study aims to identify the effect of guided visualization strategy in developing the visual perception among kindergarteners. The experimental design was used; pre-post test. A total of (32) boy and girl ranging 5 to 6 years old were selected from al-Rabeea’ kindergarten, directorate of al-karkh 2 / Baghdad. The sample divided into equal two group (16) boy and girl of each one. al-Talaqany’s (2016) visual perception skills test among kindergarteners was adopted to collect the required data. The collected data had processed based on (gender, pre-post test, and age). To achieve the objectives of the study; the researcher set up series of sessions that addressed the guided visualization strategy among kindergarteners compose
... Show More