This research was conducted to measure the safety of heat stable enterotoxin a (STa) produced by enterotoxigenic Escherichia coli, through studying its toxic effect on human blood lymphocyte, since it showed a promising effect in reducing the proliferation of colorectal cancer cells. the cytogenetic effects of (STa) by using five different concentrations (100, 200, 400, 800 and 1600μg/ml) in comparison with negative (PBS, Phosphate buffer saline) and positive (MMC, Mitomycin C) at concentration of 5μg/ml, controls on human blood lymphocytes obtained from both (10) normal healthy persons and (20) colorectal cancer patients was measured by employing the following parameters: mitotic index, blast index, chromosomal aberrations and micronucleus. On the human blood lymphocytes obtained from normal healthy persons, results showed that STa, and within all the different used concentrations, did not cause any significant cytogenetic changes in the all studied cytogenetic parameters. While on the human blood lymphocytes obtained from patients with colorectal cancer, STa was shown to cause significant decrease in both mitotic and blast index, and especially at both concentrations of (800 and 1600μg/ml) and this decrease was concentration dependent, but at the same time non significant changes were seen in both chromosomal aberrations and micronucleus parameters and for the all used concentrations. However, reduced mitotic and blast index and induced chromosomal aberrations and micronucleus frequencies of human blood lymphocytes that were obtained from both normal healthy persons and colorectal cancer patients, were observed after treatment with MMC.
Objective: To compare two positioning approaches in the surgical treatment of unstable intertrochanteric femoral fractures fixed by proximal femoral nailing, the supine versus lateral decubitus position Methodology: This randomized prospective comparative study on 26 patients with unstable intertrochanteric fractures was carried out from January 2020 and June 2022. We randomly divided patients into two groups: group A (13 patients) were operated using the traction table in the supine position for implant insertion, and group B (13 patients) were operated using the lateral decubitus position. We compared both groups regarding the setup time, operative time, tip-to-apex distance, collodiaphyseal angle, time for fluoroscopic time expo
... Show More
(1)
The litholog of Nahr Umr Formation was evaluated using the Acoustic Impedance (AI), Vp/Vs ratio cross plot colored by petrophysical properties (Vsh, PHIT, PHIE, and Sw) in Am-6-Am-10 wells. Bulk density is an important physical property that reflects matrix density and fluid density that exist in rocks pores. It is used as the main parameters to estimate physical characteristics (porosity, water saturation, shale volume, and others). AI was calculated using RHOB and VP logs. Shear velocity was calculated using Greenberg Castagna equations used for estimating the Vp/Vs ratio and the result Showed that the Nahr Umr Formation is composed of two main lithological units. The upper unit (depth 3540m -3672m) is composed of limestone (li
... Show More
The quality of groundwater is just as important as its quantity. The kinds and concentration of salts in groundwater depend on the environment, movement, and the source of the groundwater. During the field work, 20 samples have been collected from water wells from Al-Salman basin for two seasons represent wet and dry seasons in November 2017 and April 2018. After water well samples have been analyzed the Electrical conductivity values range from (2260 to 5500) μS/cm for dry season and range from (2540 to 5630) μS/cm for wet season, the Total dissolved solids values range from (1289 to 3582) ppm for dry season and range from (1710 to 3960) ppm for wet season, and pH values range from (7.11 to 7.3) for dry and wet seasons. The Hydroc
... Show More
(1)
(1)
The aim of this study to determine the genetic distance and relationship among some Iraqi date palm cultivars by using the Random Amplified Polymorphic DNA (RAPD) technique. Molecular analysis was performed by using 10 random primers. These primers produced 176 fragment lines across 14 cultivars, Of these, 166 or 94.3% were polymorphic. The size of the amplified bands ranged between 200-2250 bp. The genetic polymorphism value of each primer was determined and ranged between 7.5-16.9%. In terms of unique banding patterns, the most characteristic banding pattern was for the Barhee cultivar with primer OP-M06 and for the Khadhrawy Mandily cultivar with primer OP-C02. Genetic distance values ranged from 0.868 to 0.125 among studied date palm
... Show MoreThis research is carried out to investigate the behavior of self-compacting concrete (SCC) two-way slabs with central square opening under uniformly distributed loads. The experimental part of this research is based on casting and testing six SCC simply supported square slabs having the same dimentions and reinforcement. One of these slabs was cast without opening as a control slab. While, the other five slabs having opening ratios (OR) of 2.78%, 6.25%, 11.11%, 17.36% and 25.00%. From the experimental results it is found that the maximum percentage decrease in cracking and ultimate uniform loads were 31.82% and 12.17% compared to control slab for opening ratios (OR
... Show MoreThe aim of this study to determine the genetic distance and relationship among some Iraqi date palm cultivars by using the Random Amplified Polymorphic DNA (RAPD) technique. Molecular analysis was performed by using 10 random primers. These primers produced 176 fragment lines across 14 cultivars, Of these, 166 or 94.3% were polymorphic. The size of the amplified bands ranged between 200-2250 bp. The genetic polymorphism value of each primer was determined and ranged between 7.5-16.9%. In terms of unique banding patterns, the most characteristic banding pattern was for the Barhee cultivar with primer OP-M06 and for the Khadhrawy Mandily cultivar with primer OP-C02. Genetic distance values ranged from 0.868 to 0.125 among studied date palm
... Show More
(1)
(1)
Abstract: Aluminum alloys grade 6061-T6 are characterized by their excellent properties and processing characteristics which make them ideal for varieties of industrial applications under cyclic loading, aluminum alloys show less fatigue life than steel alloys of similar strength. In the current study, a nanosecond fiber laser of maximum pulse energy up to 9.9 mJ was used to apply laser shock peening process (LSP) on aluminum thin sheets to introduce residual stresses in order to enhance fatigue life under cyclic loading Box-Behnken design (BBD) based on the design of experiments (DOE) was employed in this study for experimental design data analysis, model building and optimization The effect of working parameters spot size (ω), scannin
... Show MoreThe paper presents the design of a system consisting of a solar panel with Single Input/Multiple Outputs (DC-DC) Buck Converter by using Simulink dialogue box tools in MATLAB software package for simulation the system. Maximum Power Point Tracking (MPPT) technique depending on Perturb and Observe (P&O) algorithm is used to control the output power of the converter and increase the efficiency of the system. The characteristics of the MSX-60 PV module is chosen in design of the system, whereas the electrical characteristics (P-V, I-V and P-I curves) for the module are achieved, that is affected by the solar radiation and temperature variations. The proposed design module has been found to be stable for any change in atmospheric tempera
... Show More
(2)